Skip to content
Seeed

Seeed

  • $6.10

    Grove Base Shield provides a simple way to connect with Arduino boards and help you get rid of breadboard and jumper wires. With the 16 on-board Grove Connectors, you can easily connect with over 300 Grove modules! The pinout of Base Shield V2 is compatible with the Arduino UNO, Arduino Leonardo ...

    View full details
    $6.10
  • $12.50

    Grove-Temperature & Humidity Sensor Pro is a high accuracy temperature and humidity sensor based on the DHT22 module (also known as AM2302 or RHT03). High-cost performance and high precision make it ideal for temperature and humidity monitoring of Arduino and Raspberry Pi, you can also use it...

    View full details
    $12.50
  • $4.90

    Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Grove modules to the Basic Shield or to other Grove compatible boards for quick prototyping. 50 cm cables

    $4.90
  • $105.50

    Beyond the Grove Shield is a bunch of Grove sensors and actuators with build-in Grove interfaces, makes your prototyping faster and easier. Simply plug in the modules and you are ready to create. Features: Various sensors and actuators Plug-and-play modules Works on a variety of Arduino-com...

    View full details
    $105.50
  • $30.70

    It is commonly found on modern machine tools and as an automotive diagnostic bus. Thanks to the CAN-BUS, makers are able to hack their cars!  It adopts MCP2515 CAN-BUS controller with SPI interface and MCP2551 CAN transceiver to give you Arduino CAN-BUS capability. Default pinout is OBD-II and C...

    View full details
    $30.70
  • $10.70

    Simply connect it to Grove - Base shield and program it, when anyone moves in its detecting range, the sensor will output HIGH on its SIG pin. Features: Grove compatible interface Adjustable detecting distance Adjustable holding time

    $10.70
  • $20.00

    Compared to LCD, OLED screens have a number of advantages such as high brightness, self-emission, high contrast ratio, slim / thin outline, wide viewing angle, wide temperature range, and low power consumption. Features: Grove compatible Interface Communicate Mode: I2C Low power consumption...

    View full details
    $20.00
  • Sold out
    $14.90

    It has a low power consumption digital chip LSM6DS3 and power supply regulator which features high sensitivity and low noise interference. It can be configured to different levels of sensitivity to acceleration and can use different ranges of angular rate measurement. It is provided with a detail...

    View full details
  • $9.80

    Grove - DPS310 is a high precision barometric pressure sensor, it can measure air pressure change caused by height changes in the centimeter level. Typical Applications: Indoor Navigation (floor detection e.g. in shopping malls and parking garages) Health and Sports (accurate elevation gain ...

    View full details
    $9.80
  • $3.80

    With this special designed conversion cables, you can easily integrate the comprehensive Grove system with breadboard or other microcontrollers that don't have compatible Grove - Base Shield yet (like the Arduino MKR family). In fact, this cable turns the 4 pin JST connectors of the atmospheric s...

    View full details
    $3.80
  • $4.00

    The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value high until a drop of water shorts the sensor trace to the grounded trace. Believe it or not this circuit will work with the digital I/O pins of your Arduino or you can use it with the analog pins...

    View full details
    $4.00
  • $6.20

    The main component of the module is a simple microphone, which is based on the LM386 amplifier and an electret microphone. This module’s output is analog and can be easily sampled and tested by an Arduino. Features: Easy to use Provides analog output signal Easily integrates with Logic modu...

    View full details
    $6.20
  • Sold out
    $19.00

    The visible portion of the OLED measures 1.12” diagonally and contains 96x96 grayscale pixels. Because the display uses OLEDs, there is no backlight, and the contrast is very high. This OLED uses the SSD1327 driver chip, which manages the display. You can communicate to the driver chip using 4-wi...

    View full details
  • Sold out
    $14.90

    The sensor(chip) used in the module is designed with Sensirion’s CMOSens® technology. The chip is well calibrated, linearized and compensated for digital output. The typical accuracy of this module can be ±2%RH (for relative humidity) and ±0.3°C (for temperature). This module is compatible with ...

    View full details
  • $3.80

    The resistance of photoresistor decreases when the intensity of light increases. A dual OpAmp chip LM358 on board produces voltage corresponding to intensity of light(i.e. based on resistance value). The output signal is an analog value, the brighter the light is, the larger the value. This modul...

    View full details
    $3.80
  • $7.50

    The X and Y axes are two ~10k potentiometers which control 2D movement by generating analog signals. The joystick also has a push button that could be used for special applications. When the module is in working mode, it will output two analog values, representing two directions. Compared to a no...

    View full details
    $7.50
  • $3.80

    The resistance of a thermistor will increase when the ambient temperature decreases. It’s this characteristic that we use to calculate the ambient temperature. The detectable range of this sensor is -40 - 125ºC, and the accuracy is ±1.5ºC

    $3.80
  • $11.20

    It can widely measure pressure ranging from 300 mbar to 1200 mbar, with a super high accuracy of 0.01mbar(0.1m) in ultra-high resolution mode. The chip only accepts 1.8V to 3.6V input voltage. However, with the outer circuit on the pcb added, this module becomes compatible with 3.3V and 5V. There...

    View full details
    $11.20
  • $4.90

    The female jumper on this cable is compatible with 2.54 pitch pin headers. With this cable, you can easily connect all of Grove modules to any 2.54 mm pitch connector.    

    $4.90
  • Sold out
    $8.40

    Breadboard 1 pin dual-male jumper wire 75pcs pack. The pack comes with 2 different lengths: 200mm (25pcs) and 100mm(50pcs). Perfect design and adequate quality for breadboard and Arduino connection, you can use it over and over again!

  • Sold out
    $17.70

    This sensor SharpGP2Y0A21YK, boasts a small package and very low current consumption, takes a continuous distance reading and returns a corresponding analog voltage with a range of 10cm (4") to 80cm (30"). It can be used in TVs, personal computers, cars and so on. Features: Grove interface co...

    View full details
  • $8.30

    The Grove - I2C Motor Driver (TB6612FNG) can drive two DC motors up to 12V/1.2A or one stepper motor up to 12V/1.2A. With the on-board MCU, it easily works with Arduino via the Grove I2C interface. This diver board is based on TB6612FNG, which is a driver IC for DC motor and stepper motor with o...

    View full details
    $8.30
  • Sold out
    $6.70

    This sensor is very simple to use, you insert in into the soil and read the data. With this sensor in the right project, your plants can let you know when it's time to water them. Features: Soil moisture sensor based on soil resistivity measurement Easy to use 2.0 cm X 6.0 cm grove module

  • $7.60

    There is a continuous-time switch on this Grove module. The output from the module switches from low (turns on) when a magnetic field (south polarity) is perpendicular to the Hall sensor and when it passes the operate point threshold BOP it switches to high (turns off) when the magnetic field dis...

    View full details
    $7.60
  • $13.40

    This sensor is designed for comprehensive monitor over indoor air condition. It's responsive to a wide scope of harmful gases, as carbon monoxide, alcohol, acetone, thinner, formaldehyde and so on. Due to the measuring mechanism, this sensor can't output specific data to describe target gases' co...

    View full details
    $13.40
  • $7.50

    A 4 digit display module usually uses 12 pins. In this Grove gadget the TM1637 is used to scale down the control pins into two Grove pins. This way It only takes two digital pins from an Arduino to control the content on the display, this even includes the luminance of the display. For projects t...

    View full details
    $7.50
  • $4.90

    It can detect the change in capacitance when a finger is nearby. This means no matter if your finger directly touches the pad or just stays close to the pad, the Grove - Touch Sensor will output HIGH.  

    $4.90
  • Sold out
    $4.90

    An infrared LED is like any other LED, with its color centered around 940nm. We can not only use the emitter to transmit data or commands, but also to emulate remotes to control your home appliance using an Arduino. The Infrared Emitter can transmit signals reliable up to 10 meters. Beyond 10 met...

    View full details
  • $5.10

    There is an IR detector on the Infrared Receiver which is used to get the infrared light emitted by the Infrared Emitter. The IR detector have a demodulator inside that looks for modulated IR at 38 KHz. The Infrared Receiver can receive signals well within 10 meters. If more than 10 meters , the ...

    View full details
    $5.10
  • $7.60

    Grove - RGB LED Stick (15-WS2813 Mini) is a cost-effective full color LED stick with 15 chainable and programmable WS2813 mini LEDs. This Grove - RGB LED stick is similar to Grove - RGB LED stick (10-WS2813 Mini) but more in the number of LEDs. It contains 15 LEDs. You can control these 15 LE...

    View full details
    $7.60
  • Sold out
    $21.30

    This module can be used to measure temperature, atmospheric pressure and humidity accurately and fast. As the atmospheric pressure changes with altitude, it can also measure approximate altitude of a place. It can be connected to a microcontroller with I2C (integrated with Grove socket) or throug...

    View full details
  • $2.50

    What does “P” mean? “P” is for “panel mount” in this product. This Grove – Button is a sister version of original Grove - Button. They are identical except the Grove connecter is moved to the back so that you can easily use it as a neat and wire-free human interface device.

    $2.50
  • $12.50

    This 3-Axis Digital Accelerometer(±16g) is based on the low power consuming IC ADXL345. It features up to 10,000g high shock survivability and has a configurable samples per second rate. For applications that don’t require too large measurement range, this is a great choice because it’s durable, ...

    View full details
    $12.50
  • $34.20

    The kit uses JGA25 DC geared motors and optical encoders for higher motor control accuracy and double-layer acrylic plates for easy placement of sensors and development boards. With this kit you can assemble your balance car, a mini Segway, or your personal project. Select the right sensor and d...

    View full details
    $34.20
  • Sold out
    $8.50

    Grove - Servo is used in driving mechanism of robots. The module is a bonus product for Grove lovers. We regulated the three-wire servo into a Grove standard connector. You can plug and play it as a typical Grove module now, without jumper wires clutter. But if you feel more like a proto servo, c...

    View full details
  • $3.80

    Through it, you can control a circuit of high voltage with low voltage, say 5V on the controller. There is an indicator LED on the board, which will light up when the controlled terminals get closed.

    $3.80
x