Products

Grove-Temperature & Humidity Sensor Pro is a high accuracy temperature and humidity sensor based on the DHT22 module (also known as AM2302 or RHT03). High-cost performance and high precision ma...

The resistance of a thermistor will increase when the ambient temperature decreases. It’s this characteristic that we use to calculate the ambient temperature. The detectable range of this sensor i...

The X and Y axes are two ~10k potentiometers which control 2D movement by generating analog signals. The joystick also has a push button that could be used for special applications. When the module...

Inside the tilt switch is a pair of balls that make contact with the pins when the case is upright. Tilt the case over and the balls don’t touch, thus not making a connection. It is wired to the SI...

It can detect the change in capacitance when a finger is nearby. This means no matter if your finger directly touches the pad or just stays close to the pad, the Grove - Touch Sensor will output HI...

Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Grove modules to the Basic Shield or to other Grove compatible boards for quick prototyping. 30 cm cables

Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Grove modules to the Basic Shield or to other Grove compatible boards for quick prototyping. 50 cm cables

The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value high until a drop of water shorts the sensor trace to the grounded trace. Believe it or not thi...

Grove Base Shield provides a simple way to connect with Arduino boards and help you get rid of breadboard and jumper wires. With the 16 on-board Grove Connectors, you can easily connect with over 3...

This shield pulls out the pins of the motherboard and expands to 8 Grove connectors, including 3 Grove digital connectors, 3 Grove analog connectors, 1 Grove I2C connector, and 1 Grove UART connect...

14 pin Female/Male header strips MKR1000 printed, very useful for board extensions. We use them extensively on Proto Shield PCB, but they are useful in any shield because of their height. Features...

This camera is based on HM01B0 QVGA monochrome rolling shutter image sensor. The sensor is an Ultra Low Power Image Sensor designed for Always-on vision devices and applications. With high light se...

The camera module is based on HM0360 VGA image sensor, which is an ultralow power, Back Side Illuminated (BSI) CMOS sensor designed for energy efficient smart vision applications, such as object-sp...

Don’t pay too much attention where to place your UNO-Type and size boards. The Holder Type Uno will help guard you boards from accidental damages. It fits every UNO sized boards, and you can choose...

Utilizing Arduino's unique 'Panini Concept' — where designers pick up a MKR board, then mix-and-match it with the desired shields and carrier boards to create custom hardware configurations for IoT...

It has only three terminals and operates on 5 V power supply. Vdd= + 5 Vdc, GND= ground, OUT= TTL signal output

Based on the ST L298N chip, this module is designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC motors, and stepper motors. It has the ability to re...

The Arduino Portenta Vision Shield is a production-ready expansion for the powerful Arduino Portenta H7. It adds a low-power camera, two microphones, and connectivity; everything you need for the r...

Begin your journey to become a maker with the Make Your UNO Soldering Bundle, which includes the Arduino Make Your UNO Kit and all the needed tools to build a soldering station at home.  With the ...

The RCWL-0516 is particularly suitable as an alternative to using a PIR motion sensor. When it detects a moving object, the output changes from a low logic level to a high level (3.3 volts). Approp...

This is a small breadboard (4,6x3,6 cm) with 170 tie points. It is self-adhesive and compatible with the Arduino Proto Shield.

A photovoltaic solar panel with extremely small dimensions, ideal for conducting experiments with solar energy.

A small polycrystalline photovoltaic cell, ideal for conducting experiments with solar energy or LED applications.

The MKR Proto Large Shield fits onto your MKR board using its provided female/male headers and enables you to fix it wherever you want with the mounting holes. This shield features a larger prototy...