Skip to content
Free shipping on all orders over $90 to a shipping address within the continental United States!*
Free shipping on all orders over $90 to a shipping address within the continental United States!*

Arduino Education Shield

SKU TSX00006 Barcode 7640152110672 Show more
Original price $20.80 - Original price $20.80
Original price
$20.80
$20.80 - $20.80
Current price $20.80
A Shield made for use with educational content.

Overview

Introduction

The Education Shield is a custom-made shield designed by Arduino Education, specially tailored for educational purposes to enable quick and easy learning while building projects. The shield is meant to be used in conjuction with the CTC Program. It connects to an Arduino 101 or UNO and extend their capabilities. The shield has a collection of features that make building small projects in or outside of the classroom easy:

  1. Reset button. When this is pressed the program uploaded to the control board is restarted.
  2. Built in protoshield or used as a placement of breadboard.
  3. Digital input and output pins. Directly connected to the digital pins on the board.
  4. I2C connector.
  5. A1 3-pin header port: Analog out/in. This can also be used as a digital in/out.
  6. D6 and D9: digital 3-pin header ports connected to digital pin 6 and 9.
  7. Speaker plug:This is connected to digital pin 11.
  8. Ground and power pins. The voltage supply pin used in CTC is the IOREF pin. This pin outputs different voltages depending on the board (101 board: 3.3V, UNO board: 5V).
  9. Analog input/output pins.
  10. SD card reader/writer connected to digital pins 10 to 13.
Note:
  • Avoid using analog A4 and A5. These have pull-up resistors connected to them and you should avoid using unless you know what you are doing.
  • Do not use digital pins 4, 10, 11, 12 and 13 when using the micro SD card reader.
  • Digital pins 9 to 13 cannot be used for capacitive sensors, these are connected to the SD card reader which has resistors and might therefore provide false readings.
  • Digital pin 6, 9 and analog pin A1 are connected to component module ports. If the ports are used don’t use the corresponding pins.
  • Digital pin 11 is connected to the audio socket. If the socket is in use don't use the  pin.
Use Modules with simple connectors

A simple 3 pin connector, that snaps in place, is used for all 3-pin modules. Here are some examples of components All these make connecting and prototyping easier through their simplified design: Push button modules, light sensor modules, and power LED modules.

If you’re trying to connect servos or other 3-pin modules, be sure about the direction of the connector so that GND is connected to GND, power to power and signal to signal. The color of a simple connector wire helps you remember it: red means power, orange or white means signal, and black means GND. Technically you can connect modules with simple connectors without 3-pin ports, as long as you plug the wires to the right pins.

 


Tech specs

Connectors

1x I2C 4-pin connector*

1x 3-pin analog connector*

2x digital 3-pin connector*

1x pwm audiojack

Plus extensions of the pins from the board.

 

*Sullins Connector Solutions SWR25X series connector, commonly called “tinkerkit” connector”

Interfaces with Arduino Board

DIO

Operating Voltage

3.3 V (Arduino 101) or 5 V (Arduino Uno)

PCB Size

53 x 71.2 mm

Conformities

The following Declarations of Conformities have been granted for this board:
REACH
For any further information about our certifications please visit docs.arduino.cc/certifications

Documentation

OSH: Schematics

The Arduino Education Shield is open-source hardware! You can build your own board using the following files:

EAGLE FILES IN .ZIP SCHEMATICS IN .PDFLIBRARY FILES IN .ZIP

Get Inspired

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare
x